Overview. This standard serves the purpose of specifying basics for tolerances and for their testing. The tolerances specified in this standard and in DIN . Page 1. Flatness Specification: DIN – Table 3. Din Eng. Uploaded by Sameh Abboud. Tolerances for Building. Copyright: © All Rights Reserved. Download as PDF, TXT or read online from Scribd.

Author:ALDEN SHUGRUE
Language:English, Spanish, Arabic
Country:Korea South
Genre:Academic & Education
Pages:476
Published (Last):27.01.2016
ISBN:561-8-34242-644-1
Distribution:Free* [*Register to download]
Uploaded by: DELMAR

69876 downloads 181476 Views 38.75MB PDF Size Report


Din 18202 Pdf

What is DIN ? DIN controls the flatness by continuously calculating the deviation of the floor from m,. m and m mean lines (the mean lines. Din Table 3 P·ermltted filatness devlaHons. Co'lumn. 2. 3. 4. 5. 6. Group. Deviations applicable to. 1 unfinished upper surfaces of floors, su bfloors. Section 5 of the German DIN (General Building Specification) relates to Further Explanatory Information · Click Here To Download Table 3 pdf.

Toleranzen im Hochbau - Bauwerke Supersedes May edition. In keeping with current practice in standards published by the International Organization for Standardization ISO , a comma has been used throughout as the decimal marker. Contents Page Foreword. Amendments The following amendments have been made in comparison with the May edition. Translation by DIN-Sprachendienst. O No pari of this translation may be reproduced without the prior permission of Ref No. This standard does not deal with deformation values as a function of time and loading. These normative references are cited at the appropriate places in the text and the titles of the publications are listed below.

Measuring points for clear dimensions in elevation table 1, group 4 El Figure 5: Checking of width 6. The grid shall be measured out. Distances between measuring points shall be selected on the lines of those shown in figures 6 and 7. Line of straightedge Figure 6 : Position deviations and distances between measuring points in a check for flatness e.

Modular size: Levels: Actual s Sections: Figure 7: Determination of actual deviations by measurement of surface levels To measure surface levels, the surface shall be divided into a grid e. The measurements shall be taken where grid lines intersect.

Din 18202 Eng

In this example, for the section between points of intersection 4 and 6, the position deviation shall be measured at the point of intersection situated at level 5, and for the section between points of intersection 5 and 10, the position deviation shall be measured at the level situated at point of intersection 7.

Explanatory notes In the following, the survey reference system for determining actual deviations from structural sizes is explained. The reference system by which to survey the building can be established in terms of position and height from fixed points.

As a rule, this point should be a point of intersection. The position of the absolute point of origin shall be such that, even after completion of the building, it remains, for surveying purposes, clearly marked, secure and accessible. The orientation of the reference system is determined by a second agreed point which should, if possible, be situated on a line of the reference system which runs through the point of origin cf.

This second point shall satisfy the same criteria as the point of origin.

DIN : Tolerances in building construction - Buildings

An easily legible graph is produced for each mean line — when the floor complies with the limits defined by the specification the graph is green and when it does not comply, the graph is red. In table 3, Group 3 and 4 relate to floor flatness, the rest is a general building specification. Data is collected by the device before being downloaded to a handheld device for analysis. Read All Testimonials. Din Table 3: Flatness tolerances Column 1 2 3 4 5 6 Group Applicable to Position deviations limit values.

F-Numbers: the Ultimate Tool for Flat Concrete Floors

Deutsches Institut fur Normung E. American Welding Society, Inc. Association Connecting Electronics Industries. CSA Group. View All Publishers.

You might also like: DAS DING MIT NOTEN PDF

Quality Management. SCC Standards Store. Popular Standards Bundles. Drawing and Drafting. Telecommunications Standards. AWS D1.

Structural Welding. The Store A2LA: Addison-Wesley Publishing Co.

Audio Engineering Society AF: American Industrial Hygiene Assn. Artech House ASA: B11 Standards Inc. Builders Hardware Manufacturers Association, Inc. Codes and Standards Training, Inc.

Chlorine Institute CIE: Clarion, Inc. Construction Specifications Institute, Inc. Product Binders DBS: DEStech Publications, Inc.

Dunedin Academic Press Ltd. Energy Institute EIA: Elevator World Inc.

Din 18202 Eng

Emergo Group, Inc. Deutsche Bundespost Telekom GA: Gypsum Association GAL: Grayboy Associates GSA: InfoComm International IP: Industrial Press, Inc. IT Governance Ltd.

Key Products, Inc. Korean Standards Association LC: Maag Gear Company, Ltd.

Meta Solutions MHI: Packt Publishing, Inc. Petroconsultants, Inc. Plasa PMI: Prentice Hall PTI:

Similar articles


Copyright © 2019 medical-site.info. All rights reserved.
DMCA |Contact Us